Unisight M4Core D-Seres Manual de usuario Pagina 45
- Pagina / 156
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digital Network Video Surveillance System
Region: Click select button, the interface is shown as in X304H304H304HFigure 4-18. Here you can set motion detection
zone. There are 396(PAL)/330(NTSC) small zones. The green zone is current cursor position. Grey zone is the
motion detection zone. Black zone is the disarmed zone. You can click Fn button to switch between the arm
mode and disarm mode. In arm mode, you can click the direction buttons to move the green rectangle to set
the motion detection zone. After you completed the setup, please click ENTER button to exit current setup. Do
remember click save button to save current setup. If you click ESC button to exit the region setup interface
system will not save your zone setup.
Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
Show message: System can pop up a message to alarm you in the local host screen if you enabled this
function.
Alarm upload: System can upload the alarm signal to the network (including alarm centre) if you
enabled current function.
Send email: System can send out email to alert you when alarm occurs.
MMS: Highlight the icon to enable this function. System can send out a message to the user once an alarm
occurs.
Period: Click set button, you can see an interface is shown as in X306H306H306HFigure 4-19X. Here you can set for
business day and non-business day. In X307H307H307HFigure 4-19X, click set button, you can see an interface is shown as in
X308H308H308HFigure 4-20. Here you can set your own setup for business day and non-business day.
Anti-dither: Here you can set anti-dither time. If you input 10 seconds here, then the motion detect signal
will last for 10 seconds and then disappear. Please note, this function is for motion detect only. It does not
support camera masking and video loss.
Alarm output: when alarm occurred, system enables peripheral alarm devices.
Tour: Here you can enable tour function when alarm occurs. It is a one-window tour. Please go to chapter
5.3.9 Display for tour interval setup.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs.
Please highlight icon to select the corresponding function. After all the setups please click save button,
system goes back to the previous menu.
Note:
In motion detection mode, you can not use copy/paste to set channel setup since the video in each
channel may not be the same.
In X309H309H309HFigure 4-18X, you can left click mouse and then drag it to set a region for motion detection. Click Fn to
switch between arm/withdraw motion detection. After setting, click enter button to exit.
Unisight Digital Technologies, Inc.
45
- M4Core D-Series Manual 1
- Features and Specifications 8
- Features 10
- Specifications 10
- Overview and Controls 15
- Hardware Mode 16
- Hardware Reset 16
- Rear Panel 17
- Connection Interface 18
- Remote Control 18
- Figure 2-4 19
- Mouse Control 20
- Virtual Keyboard 22
- Front Panel 22
- Installation and Connections 23
- Figure 3-2 24
- Figure 3-3 24
- Figure 3-4 24
- Connecting Power Supply 25
- Connecting Video Input 26
- Connecting Video Output 26
- Audio Input 26
- Audio Output 27
- Figure 3-12 29
- Alarm Input Port 30
- Alarm Output Port 30
- Figure 3-14 32
- Main Menu 33
- Figure 4-6 34
- Figure 4-7 34
- Figure 4-8 34
- Replace Button Battery 35
- Manual Record 35
- Live Viewing 35
- Figure 4-9 36
- Enable/disable record 36
- Figure 4-10 36
- Enable all channel recording 36
- Figure 4-11 36
- Search & Playback 37
- Search Menu 37
- Basic Operation 38
- Calendar 39
- Schedule Menu 40
- Figure 4-16 41
- Quick Setup 41
- Redundancy 41
- Figure 4-18 43
- Activation Snapshot 43
- 43
- Figure 4-19 43
- Priority 43
- Image FTP 44
- Go to Detect Menu 44
- Motion Detect 44
- Figure 4-22 46
- Figure 4-23 46
- Video Loss 47
- Camera Masking 47
- Go to Alarm Setup Interface 48
- Alarm Setup 48
- Figure 4-27 49
- Detect Device 50
- Figure 4-31 51
- Figure 4-32 51
- One-button Backup 52
- PTZ Control and Color Setup 52
- Cable Connection 52
- PTZ Setup 52
- Figure 4-33 53
- Figure 4-34 53
- Preset/Patrol/Pattern/Scan 54
- Preset Setup 55
- Activate Preset 56
- Patrol setup (Tour Setup) 56
- Activate Patrol (Tour) 56
- Pattern Setup 56
- Activate Pattern Function 57
- Auto Scan Setup 57
- Activate Auto Scan 57
- Figure 4-44 58
- Controls 59
- General 60
- Figure 5-17 61
- Figure 5-18 61
- Figure 5-19 62
- Figure 5-23 65
- Advanced Setup 65
- Figure 5-24 65
- IP Filter 65
- Figure 5-25 66
- Multiple Cast Setup 66
- Figure 5-26 66
- Figure 5-27 67
- NTP Setup 67
- Figure 5-28 68
- DDNS Setup 68
- Figure 5-29 68
- Figure 5-30 69
- Figure 5-31 69
- Figure 5-32 70
- Figure 5-33 70
- Alarm Center 70
- Pan/Tilt/Zoom 71
- Figure 5-35 72
- Figure 5-36 72
- Default 73
- HDD Management 74
- Alarm Output 76
- Modify Password 78
- Figure 5-45 78
- Add/Modify Group 78
- Figure 5-46 79
- Add/Modify User 79
- Figure 5-47 79
- Auto Maintain 80
- TV Adjust 80
- Config File Backup 81
- Information 81
- Figure 5-52 82
- Figure 5-53 82
- Version 83
- Online Users 83
- Shutdown 84
- About Auxiliary Menu 85
- Figure 6-48 86
- Figure 6-49 86
- Figure 6-50 86
- Patrol Setup 87
- Activate Patrol 87
- Border Setup 88
- Activate Border Function 88
- Figure 6-55 89
- WEB OPERATION 90
- Figure 7-57 91
- Figure 7-58 92
- Figure 7-59 92
- Figure 7-60 92
- Monitor Channel Menu Tree 93
- Figure 7-63 Real-time Monitor 95
- System Menu 96
- Monitor Window Switch 96
- Figure 7-66 97
- Zoom/Focus/Iris 97
- Picture Path and Record Path 99
- Configure 100
- System Information 100
- Figure 7-74 101
- HDD Information 101
- Figure 7-75 102
- System Configuration 103
- Figure 7-78 104
- Figure 7-79 104
- Figure 7-80 104
- Figure 7-81 106
- Figure 7-82 106
- Figure 7-83 108
- Schedule 108
- Figure 7-84 109
- Figure 7-85 109
- Function 111
- Network 112
- Figure 7-87 112
- Figure 7-88 113
- Figure 7-89 114
- Figure 7-90 115
- Figure 7-91 116
- Figure 7-92 117
- Figure 7-93 118
- Figure 7-94 119
- Figure 7-95 121
- Figure 7-96 121
- Figure 7-97 123
- Default & Backup 124
- Figure 7-98 124
- Advanced 125
- Alarm I/O 126
- Figure 7-100 126
- Figure 7-101 127
- Account 127
- Figure 7-102 127
- Auto Maintenance 128
- Figure 7-103 128
- Snapshot 128
- Figure 7-104 128
- Abnormality 129
- Figure 7-105 129
- Vehicle Configuration 130
- Additional Function 131
- Figure 7-107 DNS 132
- Auto Register 132
- Figure 7-108 Auto Register 132
- CDMA/GPRS 133
- Figure 7-109 CDMA/GPRS 133
- Figure 7-110 Schedule Setup 134
- Mobile Configuration 135
- Figure 7-112 138
- Figure 7-113 138
- Figure 7-114 139
- Figure 7-115 139
- Figure 7-116 Watermark 140
- Figure 7-117 142
- Figure 7-118 143
- Un-Install Web Control 144
- Daily Maintenance 150
- All Rights Reserved 156
© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales